2023 Question 1 3 out of 3 points Which of the following is not supported by Japan s Genichi Taguchi | Assignments Online

2023 Question 1 3 out of 3 points Which of the following is not supported by Japan s Genichi Taguchi | Assignments Online

Assignments Online 2023 Business Finance

Question 1

3 out of 3 points

Which of the following is not supported by Japan’s Genichi Taguchi?

Question 2

3 out of 3 points

Which of the following steps is not the same for both goods and services?

Question 3

3 out of 3 points

Which of the following is not included in a failure-mode-and-effects analysis (FMEA)?

Question 4

3 out of 3 points

In a design specification 25 ± 1.5, the value 25 is called the ____, while ± 1.5 is called the ____.

Question 5

3 out of 3 points

A system design consisting of several parallel components that function independently of each other and where the system fails only if all the parallel components fail is an example of

Question 6

3 out of 3 points

The process by which a model is constructed to test a good’s physical properties or use under actual operating conditions is called

Question 7

3 out of 3 points

In design specification terminology, permissible variation is called

Question 8

3 out of 3 points

A bank provides four sequential services to its customers. Over the last quarter, the reliability of each of these services was 92%, 97%, 95% and 90%. What is their overall reliability?

Question 9

3 out of 3 points

Which of the following is not a principal issue in service encounter design?

Question 10

3 out of 3 points

Objectives of service guarantees include all of the following except

Question 11

3 out of 3 points

Which of the following is not one of the six customer attributes that impact the design and configuration of a customer benefit package?

Question 12

3 out of 3 points

Prior to designing and configuring a customer benefit package, a firm should understand and develop its ____.

Question 13

3 out of 3 points

Which of the following is not a principal dimension of a servicescape?

Question 14

0 out of 3 points

A(n) ____ is a promise to reward and compensate a customer if a service upset occurs.

Question 15

3 out of 3 points

Which of the following is not a principal dimension of the servicescape?

Question 16

3 out of 3 points

A process map (flowchart)

Question 17

3 out of 3 points

A manufacturing firm that produces a standardized product, not made of discrete parts, with little-to-no customization, with high demand, is most likely to use this type of process.

Question 18

3 out of 3 points

Which one of the following best describes reengineering?

Question 19

3 out of 3 points

What type of process would a paper mill most likely use?

Question 20

3 out of 3 points

Ships, weddings and estate planning are examples of ____ goods and services

Question 21

3 out of 3 points

The terms, “general purpose equipment,” “flexible and capable of customizing work” and “wide variety of goods or services” best relate to

Question 22

3 out of 3 points

____ offer customers broad freedom to select the pathways that are best suited for their immediate needs and wants from many possible pathways through the service delivery system.

Question 23

0 out of 3 points

During which phase of a product’s life cycle does low unit cost become a top competitive priority?

Question 24

3 out of 3 points

A(n) ____ is a group of ____ needed to create and deliver an intermediate or final output.

Question 25

3 out of 3 points

Using the Service Positioning Matrix, a limited number of customer pathways and highly repeatable service encounter activity sequences would best relate to

Question 26

3 out of 3 points

The work activity that effectively limits throughput of a process is called a ____.

Question 27

0 out of 3 points

Which of the following is not a major activity in designing a goods-producing or service-providing process?

Question 28

0 out of 3 points

The average number of entities completed per unit time — the output rate — from a process is called ____.

Question 29

3 out of 3 points

Marketing Product Characteristics/Decisions for the Product-Process Matrix include all the following except

Question 30

3 out of 3 points

Which is the correct order of hierarchy?

 

 

 

Assignmentsonline.org help students to solve their assignment in the best possible manner. In the assignment help industry, we are regarded as one of the best helpers for students’ tasks in all subjects. We provide solutions to students from all corners of the world, but the main focus is from students residing in the US, UK, and Australia. Our primary focus is solving student assignments for all subjects and streams.

Place Order NOw

Assignment online is a team of top-class experts whose only goal is to give you the best assignment help service. Follow the link below to order now...

#write essay #research paper